Infiniti 26261-04W00 Bulb

You can Select Your Vehicle to check if 26261-04W00 fits your vehicle.

The front turn signal bulb is one of the bulbs installed in the headlight housing Lamp, that is apart of parking light, side marker light (front turn signal on 2003-2005 350Z models) and the fog light bulb on all 2007 and later G35 Sedans models. For front turn signal bulbs, remove the wheel lug nuts, jack up the car, and then remove the front wheel. To replace, first, you have to unlock the wheel well splash shield and then pull it out before replacing the bulb by turning the bulb socket Anti-Clockwise. The same procedure has got to be applied to parking the light bulbs. Similar procedures are followed in case of front side marker lights where the electric connector must be disconnected and the socket turned to be taken out. Fog light bulbs in 2007 and 2008 G35 Sedans include removing electrical connector, removing socket by turning it in anti-clockwise direction and fixing a new bulb. For the front side marker light bulbs of 2003-2006 635 sedans and the 2003-2007 635 coupes, first, remove the lens assembly then turn the socket counterclockwise and put in a new one before putting back the lens assembly. License plate light bulbs are always reached by pulling out the lens assembly of the rear bumper cover, extracting the socket, and putting in the bulb. For 635 Sedans, the main taillight assembly is fixed by disconnecting the connector which is present in the trunk trim and unscrewing the few nuts. The bulb is twisted anti-clockwise to be removed and a new bulb is fit into by practicing the twisting actions in an opposite direction. G35 Sedans have back-up lights in the trunk lid hence to get to the bulb socket, one has to first remove the trunk trim panel. For the center high-mounted brake light assembly on 350Z models, it is installed at the rear hatch, and getting to it entails having to remove the upper trim panel. Interior lights are trunk light, map light, rear lights, glove box light, instrument cluster light bulbs and clock, light bulbs for the switch panel, key lock, cylinder, and gear position indicator among others, all of which can only be reached after fully removing and installing new bulbs.

In the base model 2003 Infiniti G35 Sedan, the low-beam bulb is halogen and the high-beam and fog bulb is halogen; however, all other 2003 models and all 2004 through 2006 Sedans have Xenon low-beam bulbs and halogen high-beam and fog bulbs. Starting from 2007 MY, G35 Sedans use a single Xenon low-beam/ high-beam bulb having a tighter focus and higher intensity. The G35 Coupes that came from 2003 to 2005 have a Xenon low-beam bulb coupled with a halogen high-beam/fog light bulb Illumination while the G35 Coupes of the 2006 to 2007 models incorporate the use of a Xenon low-beam/high-beam bulb. A basic 2003 through 2005 Nissan 350Z uses two halogen bulbs, low beam and high beam, while other models from that period have a Xenon low beam bulb and a halogen high beam bulb; all these bulbs can be accessed using a single cover. During the same year, the models of 350Z also changed to a single Xenon as low beam/high beam bulb. HID headlight bulbs generate three times the light of normal halogen bulbs, requires lesser electric power and has a existence period ten times more than. They work using an AC with xenon gas similar to the gas in the vapor filled street lamp, but bare quick to warm up. Ignition is done by constructing an arc between two electrodes; a ballast transform the battery voltage to AC voltage of around 800V, the igniter regulates the voltage to fire the light then drops to the regular voltage. When it comes to bulb replacement, start by loosening the wheel lug nuts of the correct side, then jack up the car securely, next, remove the front wheel, as well as the front part of the wheel well splash shield. As with the previous step, be sure the headlights switch is off and the battery cable negative end removed, and that the windows have been lowered as on G35 Coupes and 350Z. For halogen bulbs, unscrew the bulb cover in the anti-clockwise direction, check the health of O ring seal and if damaged it has to be replaced. Remove the electrical connector from the bulb, rotate the retainer wire and get rid of the bulb and when replacing the bulb, locate the lobes of the tabs on the bulb into the slots of the housing, then secure the wire retainer, reverse the process to install the bulb.